The Crushman Trailer Unit
The NEW innovative and unique CRUSHMAN trailer
unit incorporates the original standard crusher. THE
CRUSHMAN trailer
unit is extremely practical and enables recycling on-site!
Save money on skips, save
money on aggregate costs! Re-use previously unusable
material as your hardcore for the new build or to sell
on! As THE CRUSHMAN Trailer
Unit is only the size of a small car, access is not usually
an issue but there are some situations
where access is extremely restricted and in these instances, THE
CRUSHMAN may
be removed from the trailer unit via the fork lift tunnels
provided on the unit and used on a
stand which is available as an accessory. (see photo below
and accessories
page).
THE CRUSHMAN'S sturdy
cabinet houses its own power source, provided
by an Atlas Copco 30 ltr Honda power pack (LP13-30 P PAC
- see separate specification). Other accessories
or tools such as the breaker and hoses may be stored in
here too.
The Crushman:
- Crushes at a rate of 2 - 3 tons
per hour
- Accepts lumps of approximately 200 x 150 mm cross-section. (It is best to feed large lumps individually)
- For occasions when the Crusher
is to be used when removed from the Trailer Unit, adaptor
plates/tractor linkages are
available for a wide range of host vehicles such as agricultural
tractors, skidsteers and compact loaders.
- The Crushman has replaceable crushing plates and hydraulic oil filter to ensure a long working life.
- Available in yellow, red or
green. Your individual colour specification
can be met for a small extra cost - see Accessories
page.
   
The Crushman Trailer Technical Specifications
| Unit Weight |
1200 kg |
Ball
hitch |
50mm |
| Typical Loaded Weight |
1250 kg |
Min
Hydraulic Oil Flow |
20
lmp |
| Height |
1777 mm |
Max
Hydraulic Oil Flow |
60
lmp |
| Width |
1600 mm |
Min
Oil Pressure |
2000
psi
(140 bar) |
| Length |
3000
mm |
Max
Oil Pressure |
3000
psi
(205 bar) |
| Cabinet
internal length |
1200
mm |
Linkage
type |
Quick
Release
|
| Cabinet
internal width |
775
mm |
Operational
Noise Level for Crusher: |
| Cabinet
internal height |
1075
mm |
Unloaded
|
79.9
db (A)
|
| Cabinet
door opening width |
740mm |
Loaded
|
85.0
db(A)
|
| Wheel
size |
5.00x10
- 8 ply |
|
|
Filter change every 400 hours -
more frequently if the flow indicator shows red.
- Filter element £90 plus VAT
- Replacement plate cost = £325
plus VAT
- Replacement hopper = £450 plus
VAT
- Alternative adaptor (Tractor Linkage)
= £370
Atlas Copco hydraulic power pack technical specification
| Engine |
Engine Honda GX390 QX, air cooled 1 cylinder 4 stroke petrol engines with oil alert system and transistor ignition system. |
| Performance |
13HP (9.6KW) at 3600 rpm |
| Fuel |
Petrol |
| Starter |
Recoil hand start |
| Oil
Flow |
20-30
l/min (5.2-7.9gal, US) |
| Circuit type |
Open Centre |
| Pump type |
Gear pump, directly driven from the engine crankshaft by means of a flexible coupling
|
| Filtration |
Filtration
25 u filter in return line. Filter by-pass valve
in valve block.
|
| Cooling
system |
Thermostatically
controlled air blast oil cooler |
| Fuel Tank |
6.5 (1.7) Unleaded petrol |
| Hydraulic
fluid |
7.0
(1.8) Mobil EAL 224 or similar |
| Recommended
safe working load for slings |
500kg |
Operational noise level: refer
to manual.
Flow Rates
The European Hydraulic Tool Manufacturers
Association (E.H.T.M.A) has categorised hydraulic power
packs and tools in terms of flow rate and working pressure.
The LP 13-30 PAC is categorised by the E.H.T.M.A as below:
| Flow Rate, L.P.M (Gal, US) |
20-30 (5.2 - 7.9) |
| Nominal Pressure,
Bar (PSI) |
120 (1740) |
| Max Pressure, Bar (PSI) |
138 (2001) |
| E.H.T.M.A Category |
C and D |
** Due to continual research and development, we reserve to right to change specifications listed. |
